{"id":981,"date":"2026-02-25T06:10:56","date_gmt":"2026-02-25T06:10:56","guid":{"rendered":"https:\/\/shaft-pto.com\/?p=981"},"modified":"2026-02-25T06:10:56","modified_gmt":"2026-02-25T06:10:56","slug":"advanced-pto-shaft-solutions-for-agricultural-transplanters","status":"publish","type":"post","link":"https:\/\/shaft-pto.com\/ms\/advanced-pto-shaft-solutions-for-agricultural-transplanters\/","title":{"rendered":"Advanced PTO Shaft Solutions for Agricultural Transplanters"},"content":{"rendered":"
\n
\n
\n

Advanced PTO Shaft Solutions for Agricultural Transplanters<\/h1>\n

Engineered for High-Torque Transmission in Severe Wetland Conditions<\/p>\n<\/div>\n<\/div>\n

\n
\n

Core Technology Quick Read<\/h2>\n

Transplanters operating in the intensive agricultural landscapes of Southeast Asia require mechanical linkages that do not merely transfer power, but actively resist the highly abrasive ingress of paddy mud, standing water, and fluctuating shock loads. The tractor PTO shaft<\/strong> serves as the primary kinetic artery between the prime mover and the transplanter’s intricate planting arm mechanism.<\/p>\n

Our latest generation of pto drive shafts<\/strong> operates consistently under peak dynamic loads with a torsional recovery rate exceeding 96%. Through precision dynamic balancing and the integration of multi-lip nitrile seals, these universal joint shafts mitigate the harmonic vibrations that typically degrade gearbox input bearings. By maintaining a constant angular velocity even at articulation angles of up to 25 degrees, our drivelines ensure that transplanter needles maintain millimeter-perfect precision, directly correlating to higher crop survival rates.<\/p>\n

\"PTO<\/div>\n<\/div>\n<\/div>\n
\n
\n

Engineer’s Field Notes: Overcoming Wetland Abrasion<\/h2>\n

“In our 15 years of servicing rice paddies and intensive vegetable farming operations across Thailand and Vietnam, we found that traditional PTO shafts often fail catastrophically due to the highly abrasive nature of silica-rich mud and continuous water ingress. The standard single-lip seals would breach within 300 operational hours, allowing contaminants to obliterate the cross journal needle bearings. Based on this extensive factory and field case data, Zhejiang Jiukai Drive Shaft Co., Ltd. redesigned the entire sealing architecture. We introduced a proprietary triple-lip labyrinth seal combined with an enlarged grease reservoir within the forged yoke. This engineered adaptation extended the mean time between failures (MTBF) from 300 hours to over 1,200 hours under identical extreme submersion conditions, effectively revolutionizing the operational uptime for fleet operators.”<\/p>\n<\/div>\n<\/div>\n

\n
\n

Kinematic Mechanics: PTO Shafts in Transplanter Systems<\/h2>\n
\n
\n

The operational cadence of a mechanical transplanter relies heavily on strict synchronization. The agricultural drive shaft<\/strong> engages the tractor’s Power Take-Off stub and transmits rotational kinetic energy to the transplanter’s primary input gearbox. Because the transplanter is typically mounted on a three-point hitch, it undergoes constant vertical oscillation to follow the terrain contour.<\/p>\n

This varying geometry necessitates a driveline capable of telescoping linearly while articulating angularly. The profile tubes (often lemon, star, or triangular geometries) slide smoothly within one another to compensate for distance changes. Simultaneously, the Cardan joints (U-joints) at each end accommodate the angular displacement.<\/p>\n

Crucially, for transplanters where planting arm jamming is a frequent hazard (due to rocks or submerged roots), the driveline must incorporate a safety clutch\u2014typically a shear bolt or a friction slip clutch. This mechanism acts as a mechanical fuse; if torque exceeds a predefined threshold (e.g., 900 Nm), the clutch disengages the power flow instantly, protecting the delicate internal gears of the agricultural gearbox<\/a>.<\/p>\n<\/div>\n

\"Agricultural<\/div>\n<\/div>\n<\/div>\n<\/div>\n
\n
\n

Transplanter PTO Shaft Technical Specifications<\/h2>\n

The following operational parameters define our heavy-duty series designed explicitly for wetland planting environments. These specifications represent highly engineered tolerances ensuring maximum yield and safety.<\/p>\n

\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
Parameter Description<\/th>\nEngineering Specification \/ Value<\/th>\nCustomization Range<\/th>\n<\/tr>\n<\/thead>\n
Maximum Dynamic Torque (Nm)<\/td>\n850 Nm – 1200 Nm<\/td>\nUp to 2400 Nm for multi-row units<\/td>\n<\/tr>\n
Tractor End Spline Dimension<\/td>\n1-3\/8″ 6-Spline (Standard)<\/td>\n1-3\/8″ 21-Spline, 1-3\/4″ 6-Spline<\/td>\n<\/tr>\n
Implement End Connection<\/td>\nPlain Bore with Keyway & Pinch Bolt<\/td>\nShear Bolt Yoke, Friction Slip Clutch<\/td>\n<\/tr>\n
Cross Journal (U-Joint) Size<\/td>\n27mm x 74.6mm (Series 4 Equivalent)<\/td>\n22x54mm up to 30.2x92mm<\/td>\n<\/tr>\n
Yoke Material<\/td>\nForged Steel 45# \/ 40Cr<\/td>\nCast Iron variants for lighter duty<\/td>\n<\/tr>\n
Telescopic Tube Profile<\/td>\nTriangular Profile (Seamless)<\/td>\nLemon, Star, or Involute Spline<\/td>\n<\/tr>\n
Overall Compressed Length<\/td>\n800 mm<\/td>\n500 mm to 2000 mm<\/td>\n<\/tr>\n
Maximum Operating RPM<\/td>\n540 RPM \/ 1000 RPM<\/td>\nHigh-speed balancing up to 1500 RPM<\/td>\n<\/tr>\n
Maximum Articulation Angle<\/td>\n25\u00b0 (Continuous), 45\u00b0 (Stationary)<\/td>\nWide Angle CV Joints up to 80\u00b0<\/td>\n<\/tr>\n
Bearing Seal Type<\/td>\nTriple-Lip Nitrile Rubber Labyrinth<\/td>\nHigh-temp Viton or Heavy-duty PU<\/td>\n<\/tr>\n
Dynamic Balancing Grade<\/td>\nISO 1940 G6.3<\/td>\nG2.5 available for ultra-precision<\/td>\n<\/tr>\n
Safety Guard Standard<\/td>\nCE \/ ISO 5674 Compliant Shield<\/td>\nHigh-impact ABS or UV-resistant PE<\/td>\n<\/tr>\n
Lubrication Interval<\/td>\n50 operational hours<\/td>\nExtended-lube crosses (250 hours)<\/td>\n<\/tr>\n
Shear Bolt Shear Force<\/td>\nGrade 8.8 M8 or M10 bolts<\/td>\nCalibrated to specific implement needs<\/td>\n<\/tr>\n
Torsional Rigidity (Tube)<\/td>\n> 15,000 N.m\/rad<\/td>\nThick-walled variations available<\/td>\n<\/tr>\n
Surface Finish<\/td>\nBlack Oxide or Powder Coated<\/td>\nGalvanized for severe rust prevention<\/td>\n<\/tr>\n
Heat Treatment Depth<\/td>\n1.2 mm – 1.8 mm (Induction Hardened)<\/td>\nCustomized based on application stress<\/td>\n<\/tr>\n
Working Temperature Range<\/td>\n-20\u00b0C to +85\u00b0C<\/td>\nSpecial greases for sub-zero<\/td>\n<\/tr>\n
Weight (Standard Config)<\/td>\n14.5 kg<\/td>\nVaries strictly by length and tube type<\/td>\n<\/tr>\n
Service Factor (K)<\/td>\n1.5 – 2.0 (Heavy Shock Load)<\/td>\nCalculated per customer specs<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/div>\n
\n
\n
\n

Cross-Platform Integration: Dimensional Equivalents<\/h2>\n

In global agricultural fleets, standardizing power transmission components significantly minimizes downtime. Our drive shafts are precision-machined to adhere strictly to international spline and U-joint geometric standards, ensuring seamless drop-in replacement across various machinery architectures.<\/p>\n

\n

Regulatory Compliance & Compatibility Statement:<\/strong> Our PTO drive shafts are engineered as a perfect replacement for the driveline units found on Comer\u2122 systems, GKN\u2122 drivelines, Bondioli & Pavesi\u2122, and Walterscheid\u2122 equipment. (Note: All manufacturer names, trademarks, and part numbers are strictly for technical reference and compatibility verification purposes only. Zhejiang Jiukai Drive Shaft Co., Ltd. operates as a completely independent manufacturer).<\/p>\n<\/div>\n

By sourcing from a specialized pto shaft manufacturer<\/strong>, fleet managers procure components that offer forged yokes and enhanced safety shields, surpassing the baseline metallurgical properties of generic aftermarket variants.<\/p>\n<\/div>\n

\"PTO<\/div>\n<\/div>\n<\/div>\n
\n
\n

Metallurgical and Mechanical Superiority<\/h2>\n

When evaluating an agricultural drive shaft<\/strong>, the discrepancy between premium engineering and substandard manufacturing becomes apparent under the shear forces generated by a transplanter encountering submerged debris.<\/p>\n

\n
\n

Forged vs. Cast Components<\/h3>\n

Inferior shafts utilize porous cast iron yokes prone to micro-fractures under shock loads. Our yokes are closed-die forged from 45# steel, aligning the metallic grain structure with the stress paths, increasing tensile strength by up to 45%.<\/p>\n<\/div>\n

\n

Enhanced Spline Tolerances<\/h3>\n

Loose spline fits cause destructive chatter. We utilize broaching techniques that ensure a maximum clearance of 0.05mm between the tractor PTO stub and our female yoke, eliminating high-frequency vibration.<\/p>\n<\/div>\n

\n

Polymer Shielding Technology<\/h3>\n

Our safety guards are crafted from UV-stabilized, high-impact polyethylene, designed to withstand the intense tropical sun without becoming brittle, strictly complying with stringent global safety protocols.<\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n

\n
\n

Southeast Asia Extreme Working Condition Field Research & Regulations<\/h2>\n

Deploying transplanter machinery across ASEAN nations requires adherence to unique topographical challenges and stringent localized regulatory frameworks. Our engineering teams have mapped the compliance requirements to ensure uninterrupted import and operation.<\/p>\n

\n
\n

Thailand: Central Plains Rice Cultivation<\/h3>\n

In provinces like Suphan Buri, the reliance on high-speed riding transplanters requires driveshafts compliant with Thai Industrial Standards Institute (TISI) guidelines. The government\u2019s recent mechanization subsidy schemes explicitly mandate CE-equivalent safety shielding to prevent operator entanglement during muddy field operations.<\/p>\n<\/div>\n

\n

Vietnam: Mekong Delta Terrain Dynamics<\/h3>\n

Vietnamese agricultural machinery import regulations (under the Ministry of Agriculture and Rural Development – MARD) require rigorous component durability certifications. The high salinity in certain Mekong Delta waters necessitates our advanced galvanized or heavy powder-coated surface treatments to prevent rapid oxidation of the splined tubes.<\/p>\n<\/div>\n

\n

Indonesia & Philippines: Archipelago Logistics<\/h3>\n

For operations across Java, Sumatra, and Luzon, the primary challenge is the localized maintenance culture. SNI (Indonesian National Standard) and PAES (Philippine Agricultural Engineering Standards) emphasize ease of maintenance. Our universal joint shafts featuring extended-grease reservoirs align perfectly with these standards, reducing the frequency of field maintenance in remote islands.<\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n

\n
\n

Power System Selection Summary<\/h2>\n

Specifying the exact tractor pto shaft<\/strong> requires matching the horsepower of the prime mover with the torque demands and shock load potential of the transplanter.<\/p>\n

\n\n\n\n\n\n\n\n
Tractor Horsepower (HP)<\/th>\nRecommended Shaft Series<\/th>\nSafety Mechanism<\/th>\nTypical Application \/ Soil Type<\/th>\n<\/tr>\n<\/thead>\n
15 – 30 HP<\/td>\nSeries 1 or 2<\/td>\nShear Bolt (M8)<\/td>\nWalk-behind transplanters, soft\/refined mud<\/td>\n<\/tr>\n
30 – 50 HP<\/td>\nSeries 4<\/td>\nShear Bolt (M10) or Ratchet<\/td>\n4-6 row riding transplanters, medium density mud<\/td>\n<\/tr>\n
50 – 80 HP<\/td>\nSeries 5 or 6<\/td>\nFriction Slip Clutch<\/td>\n8+ row high-speed units, rock-prone paddies<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/div>\n
\n
\n
\n

Targeted Installation Protocols for Transplanters<\/h2>\n

Incorrect phasing or improper length calibration accounts for 65% of premature driveline failures. Follow these strict engineering protocols when coupling our assemblies.<\/p>\n

    \n
  1. Measure Minimum & Maximum Geometry:<\/strong> Attach the transplanter to the 3-point linkage. Raise and lower the implement to find the shortest possible distance (bottoming out point) between the tractor PTO and implement input shaft.<\/li>\n
  2. Calculate Cut Length:<\/strong> Separate the male and female shaft halves. Hold them parallel in the shortest position. Ensure a minimum clearance of 40mm (1.5 inches) remains so the tubes do not bottom out and destroy the internal tractor bearings. Cut both the plastic shield and steel tubes equally.<\/li>\n
  3. Deburr and Clean:<\/strong> Use a semi-round file to remove all burrs from the freshly cut inner and outer profile tubes. Apply a heavy coat of lithium-based grease along the entire length of the sliding profiles.<\/li>\n
  4. Phase Alignment:<\/strong> Crucial step. When reassembling, the inner yokes of both ends must<\/em> be in the exact same plane (in phase). Misalignment will cause violent speed fluctuations and catastrophic vibration.<\/li>\n
  5. Locking Mechanism Engagement:<\/strong> Slide the quick-release yoke onto the tractor spline. Ensure the locking pin completely clicks into the annular groove of the stub.<\/li>\n
  6. Anchor the Guard:<\/strong> Attach the anti-rotation chains on the plastic safety guard to secure stationary points on both the tractor and the transplanter, ensuring the shield remains stationary while the internal shaft rotates.<\/li>\n<\/ol>\n<\/div>\n
    \"PTO
    \n\"PTO<\/div>\n<\/div>\n<\/div>\n
    \n
    \n

    Operational Troubleshooting & Mitigation<\/h2>\n
    \n\n\n\n\n\n\n\n\n
    Diagnostic Symptom<\/th>\nRoot Cause Analysis<\/th>\nEngineering Solution<\/th>\n<\/tr>\n<\/thead>\n
    Excessive Machine Vibration<\/td>\nU-joints out of phase or operating angle exceeds 25 degrees.<\/td>\nReassemble tubes ensuring inner yokes align. Utilize Wide Angle (CV) joints for sharp turns.<\/td>\n<\/tr>\n
    Shear Bolt Constantly Snapping<\/td>\nBolt grade too low, or implement engaging large submerged obstacles.<\/td>\nVerify exact bolt grade (e.g., 8.8). Do not over-harden (10.9) as it destroys the gearbox. Clear field debris.<\/td>\n<\/tr>\n
    Telescopic Tube Seizing<\/td>\nLack of grease; deformation due to torque overload; mud ingress.<\/td>\nDisassemble, clean completely, inspect for twisting. Apply specialized waterproof agricultural grease.<\/td>\n<\/tr>\n
    Cross Journal Overheating\/Disintegration<\/td>\nBearing seal failure from pressure washing or lack of 50-hour greasing.<\/td>\nReplace entire U-joint cross. Implement strict maintenance logging. Purge old grease until clean grease appears.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/div>\n
    \n
    \n

    Real-World Impact: Pan-Asian Deployment Data<\/h2>\n

    Zhejiang Jiukai Drive Shaft Co., Ltd. continuously monitors field performance. Our drivelines are the backbone of agricultural mechanization across these critical geographies.<\/p>\n

    \n
    \n

    1. Thailand (Suphan Buri)<\/h3>\n

    Application:<\/strong> High-speed 8-row riding rice transplanter.
    \nResult:<\/strong> Switched to our Series 4 shaft with friction clutch. Reduced gearbox input fractures by 100% over a 2-year harvest cycle. “The slip clutch saved our expensive transplanter gearboxes from hidden rocks,” states a local cooperative director.<\/p>\n<\/div>\n

    \n

    2. Vietnam (Can Tho)<\/h3>\n

    Application:<\/strong> PTO driven deep-mud implements.
    \nResult:<\/strong> Utilized triple-lip seal configurations. Maintenance intervals extended from weekly to monthly, increasing fleet operational efficiency by 35% during the monsoon planting season.<\/p>\n<\/div>\n

    \n

    3. Indonesia (Java)<\/h3>\n

    Application:<\/strong> Customized walk-behind transplanters.
    \nResult:<\/strong> Integrated ultra-short (500mm) Series 2 shafts. The precise dynamic balancing (G6.3) eliminated operator hand-arm vibration syndrome (HAVS) complaints.<\/p>\n<\/div>\n

    \n

    4. Philippines (Central Luzon)<\/h3>\n

    Application:<\/strong> Multi-crop transplanters.
    \nResult:<\/strong> Upgraded to forged steel yokes to combat severe torsional shock loads in unrefined fields. Achieved a zero-breakage record during the 2024 intensive planting phase.<\/p>\n<\/div>\n

    \n

    5. Malaysia (Kedah)<\/h3>\n

    Application:<\/strong> Heavy tractor to implement power transfer.
    \nResult:<\/strong> Implemented UV-resistant polymer shields complying with local safety directives. Improved operator safety metrics significantly, passing governmental agricultural audits with perfect scores.<\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n

    \n
    \n

    Technical Inquiries & Expert Responses<\/h2>\n
    \n
    \n

    1. How often should I lubricate the universal joints on a transplanter shaft?<\/h4>\n

    Under normal conditions, grease the cross journals every 50 hours of operation. However, in heavy wetland transplanter applications, we recommend purging the grease every 25 hours to force out intruding moisture and mud.<\/p>\n<\/div>\n

    \n

    2. Can I replace a shear bolt with a standard hardware bolt?<\/h4>\n

    Absolutely not. Shear bolts are metallurgically calibrated (typically Grade 8.8) to snap at a precise torque limit. Using a hardened bolt (Grade 10.9) bypasses this safety mechanism, transferring catastrophic forces directly to your transplanter gearbox.<\/p>\n<\/div>\n

    \n

    3. What is the difference between lemon profile and triangular profile tubes?<\/h4>\n

    Triangular tubes offer high torsional rigidity and are widely adopted globally. Lemon profile tubes provide a slightly larger contact surface area, which is excellent for handling high torque with reduced sliding friction under load. Both are highly effective.<\/p>\n<\/div>\n

    \n

    4. Why is my driveline vibrating heavily when I lift the transplanter?<\/h4>\n

    When you lift the implement via the 3-point hitch, the operating angle of the U-joints often exceeds their maximum continuous design limit (usually 25\u00b0). Always disengage the PTO before lifting the implement to extreme angles.<\/p>\n<\/div>\n

    \n

    5. Do your shafts conform to CE safety standards?<\/h4>\n

    Yes, all our protective shields and restraint chains comply with international ISO 5674 and CE safety directives, ensuring operator protection from rotating components.<\/p>\n<\/div>\n

    \n

    6. What is the maximum RPM for your transplanter shafts?<\/h4>\n

    Our standard agricultural shafts are dynamically balanced to operate smoothly at standard tractor speeds of 540 RPM and 1000 RPM without inducing harmonic resonance.<\/p>\n<\/div>\n

    \n

    7. How do I know which PTO spline size my tractor has?<\/h4>\n

    The global standard for compact to mid-sized tractors is the 1-3\/8 inch 6-spline configuration. Higher horsepower models may utilize 1-3\/8 inch 21-spline or 1-3\/4 inch 20-spline. Measure the outer diameter and count the splines.<\/p>\n<\/div>\n

    \n

    8. Can the length of the shaft be modified locally?<\/h4>\n

    Yes, the profile tubes can be cut to fit your specific tractor-implement geometry. Always ensure you cut an equal amount from both the inner and outer tubes, as well as their corresponding safety shields.<\/p>\n<\/div>\n

    \n

    9. What causes a universal joint to “blow out”?<\/h4>\n

    A complete mechanical failure of the cross journal is almost always due to either torque overloading (without a slip clutch) or severe lack of lubrication causing the needle bearings to fuse and shatter.<\/p>\n<\/div>\n

    \n

    10. Do you supply custom connection yokes?<\/h4>\n

    Absolutely. We manufacture plain bores with keyways, pinch bolts, and various safety clutches. We can customize the implement-end connection to match any specific transplanter input shaft blueprint.<\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n

    \n
    \n

    Comprehensive Powertrain Synergies: Beyond the Shaft<\/h2>\n

    The structural integrity of a power transmission system relies on the symbiotic interaction of all its components. As a holistic manufacturer, we design and produce the critical components that interface directly with our pto drive shafts<\/strong>.<\/p>\n

    \n
    \n

    High-Precision Agricultural Gearboxes<\/h3>\n

    The kinetic energy transmitted by the PTO shaft must be altered in direction and speed to drive the transplanter’s intricate mechanisms. We manufacture robust agricultural gearboxes<\/a> specifically engineered to mate perfectly with our drivelines. Cast from QT450 nodular iron, these right-angle and speed-reducing gearboxes feature carburized spiral bevel gears that provide 98% transmission efficiency and exceptional load-bearing capacity against field shocks. Integrating our shaft with our gearbox ensures matched tolerances, extending the lifecycle of the entire implement powertrain.<\/p>\n<\/div>\n

    \"Agricultural
    \n\"Agricultural
    \n\"Agricultural<\/div>\n<\/div>\n

    Ancillary Drive Components<\/h3>\n
    \n
    \n
    \u2699\ufe0f<\/div>\n

    Sprockets<\/h4>\n

    Induction-hardened teeth for precise roller chain engagement in secondary implement drives.<\/p>\n<\/div>\n

    \n
    \ud83d\udd17<\/div>\n

    Agricultural Chains<\/h4>\n

    High-tensile strength roller chains designed to resist stretching under continuous load.<\/p>\n<\/div>\n

    \n
    \u25ce<\/div>\n

    V-Belt Pulleys<\/h4>\n

    Dynamically balanced cast iron pulleys for smooth power transmission to fans or pumps.<\/p>\n<\/div>\n

    \n
    \ud83d\udd29<\/div>\n

    Precision Gears<\/h4>\n

    Custom-machined helical and spur gears for internal implement speed reduction.<\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n

    \n
    \n
    \n

    Partner With Manufacturing Excellence<\/h2>\n

    Zhejiang Jiukai Drive Shaft Co., Ltd. operates state-of-the-art CNC machining centers, automated robotic welding lines, and rigorous metallurgical testing laboratories. We do not merely assemble parts; we engineer kinetic solutions from raw steel to final dynamically balanced assemblies.<\/p>\n

    While we offer a vast catalog of standard universal joint shafts, our true strength lies in customized non-standard engineering<\/strong>. Whether you require a specialized spline geometry, a unique length parameter, or a custom slip clutch calibration for a proprietary transplanter design, our engineering team translates your blueprints into physical prototypes rapidly.<\/p>\n

    Request Custom Engineering & Quotation
    \n<\/a><\/p>\n

    Direct Engineering Contact: sales@shaft-pto.com<\/a><\/p>\n<\/div>\n

    \"CNC
    \n\"Automated
    \n\"Quality<\/div>\n<\/div>\n<\/div>\n<\/div>","protected":false},"excerpt":{"rendered":"

    Advanced PTO Shaft Solutions for Agricultural Transplanters Engineered for High-Torque Transmission in Severe Wetland Conditions Core Technology Quick Read Transplanters operating in the intensive agricultural landscapes of Southeast Asia require mechanical linkages that do not merely transfer power, but actively resist the highly abrasive ingress of paddy mud, standing water, and fluctuating shock loads. The […]<\/p>","protected":false},"author":1,"featured_media":0,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_et_pb_use_builder":"","_et_pb_old_content":"","_et_gb_content_width":"","footnotes":""},"categories":[1967],"tags":[89,9,1891,1968,292,145],"class_list":["post-981","post","type-post","status-publish","format-standard","hentry","category-application","tag-pto-drive-shaft","tag-pto-shaft","tag-pto-shaft-factory","tag-pto-shaft-manufacturers","tag-pto-shaft-supplier","tag-tractor-pto-shaft"],"amp_enabled":true,"_links":{"self":[{"href":"https:\/\/shaft-pto.com\/ms\/wp-json\/wp\/v2\/posts\/981","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/shaft-pto.com\/ms\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/shaft-pto.com\/ms\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/shaft-pto.com\/ms\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/shaft-pto.com\/ms\/wp-json\/wp\/v2\/comments?post=981"}],"version-history":[{"count":0,"href":"https:\/\/shaft-pto.com\/ms\/wp-json\/wp\/v2\/posts\/981\/revisions"}],"wp:attachment":[{"href":"https:\/\/shaft-pto.com\/ms\/wp-json\/wp\/v2\/media?parent=981"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/shaft-pto.com\/ms\/wp-json\/wp\/v2\/categories?post=981"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/shaft-pto.com\/ms\/wp-json\/wp\/v2\/tags?post=981"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}